Application Notes (Sorted By Date)
- Analysing external bus operation (03/05/12)
- Communicate with EEPROM using RIIC (21/03/12)
- Slave transmission/reception through serial interface IICA (09/03/12)
- Master transmission/reception through serial interface IICA (08/03/12)
- Special considerations for MAX14820/MAX14821 sensor/actuator transceivers (09/02/12)
- Understanding internal test pattern generation (11/01/12)
- Production testing of CC85xx audio transceiver (09/11/11)
- Implement transceiver with minimal protocol (24/10/11)
- Features, uses of zero copy Ethernet driver (19/10/11)
- Employ CDCE62005 as clock synthesiser, jitter cleaner (14/10/11)
- Implementing thermocouple interface with MSP430F5529 MCU (11/10/11)
- Accessing 16bit I2C register addresses (25/08/11)
- Assessing link quality with MAX9259/MAX9260 evaluation kits (24/08/11)
- Crystal selection guide (11/08/11)
- Wireless microphone with USB interface (10/08/11)
-
Protecting RS-485 interfaces against lethal electrical transients
(08/06/11)
-
TPIC6C596 input interface routing
(07/06/11)
-
Sense multiple pushbuttons using only two wires
(11/05/11)
-
78Q8430 10/100 Ethernet MAC and PHY
(06/05/11)
-
Teridian 78Q8392L compatibility
(05/05/11)
-
Design guidelines for 78P235x E4/STM1e LIUs
(04/05/11)
-
RS-485 adapter converts data lines from full- to half-duplex
(11/04/11)
-
RIIC single-master communication
(25/03/11)
-
Generating 44.1kHz based clocks with LMH1983
(04/03/11)
-
Using IIC3 to reprogram flash memory in user program mode
(02/03/11)
-
Clock synchronous serial I/O with chip select (SSU)
(21/02/11)
-
Ethernet transmit and receive settings
(16/02/11)
-
Continuous data streaming apps with CC110x and CC2500
(14/02/11)
-
TLK6002 board design guide
(08/02/11)
-
Analog switch multiplexes SFP modules
(01/02/11)
-
Compliance testing for display port cable
(13/01/11)
-
Compliance testing for USB 3.0 connectors
(12/01/11)
-
Change radio register parameters for SimpliciTI app
(07/01/11)
-
Design with 2.4 GHz YAGI PCB antenna
(06/01/11)
-
One-way or two-way audio comm using RF transceiver and codec
(05/01/11)
-
How to connect AIF2 to FFTC
(04/01/11)
-
Guide to antenna interface migration
(03/01/11)
-
Boost robustness of channel link design
(27/12/10)
-
How to use demo board for NFC chip
(21/12/10)
-
LMH6629 LNA evaluation board
(15/12/10)
-
Specs for EMI hardened op amps
(14/12/10)
-
Guide to using LM49250 evaluation board
(13/12/10)
-
Measure settling time for monolithic 18-Bit DAC
(10/12/10)
-
Understanding I2C-bus extender
(09/12/10)
-
Using standalone high speed CAN transceiver
(08/12/10)
-
PLL through dynamic reconfiguration port
(07/12/10)
-
SFI-4.1 SDR interface with bus alignment
(06/12/10)
-
Using CEC with HDMI transmitter
(29/11/10)
-
Programming the MAX1441 with a USB-to-JTAG interface board
(14/09/10)
-
Interface code implementation for the MAX9635 ambient light sensor
(14/09/10)
|
||||||||
|
||||||||
Hot Articles
Tear Down

Sneak a peek inside popular products!
iPhone 4 design exhibits high reuse 
The new Apple iPhone 4 could very well be called an iPad since it uses at least seven chips from the popular Apple tablet, according to analysts from UBM TechInsights.
Search EE Times India
Top Ranked Articles
- Smartphone with dual-side display; courtesy Microsoft
- Graphene interconnects outperform copper
- PCIe 3.0 cores offer low power, latency
- PXI Express switches boost test system flexibility
- Altera rolls out Stratix IV GX FPGA devt kit
- Chip supports DisplayPort to HDMI conversion
- Rambus tech aims at 2011 and beyond
- SuperSpeed USB transceiver chip rolls
- FPGA framework simplifies app implementation
- Energy-saving PCs consume 80% less power












